Dear Customer,
Thank you for purchasing this product. This document collect all the necessary information for the installation and use of this accessory

Need help ?
Write in the Forum on the www.RosettaCNC.com site or send an email to the following address: support@rosettacnc.com, the RosettaCNC development team will be happy to answer you in a short time.

For the manual movements (jog) there is a RosettaCNC Handwell A accessory. It has an ergonomic shape that makes it easy to use And is contained in a sturdy anti-shock box. It is equipped with magnets that guarantee a reliable fixation, The electrical connection cable with the RosettaCNC controller It is equipped with a steel wire that increases its reliability and a removable connector with anti-vibration spring contacts.

Handwell B has :

• a double enable command button
• the emergency button with two contacts
• a selector for choosing the axis on which to act
• a three-position switch 1 – 1/10 – 1 /100 that defines the encoder unit of measurement.
• an encoder to execute the movement of the selected axis
• three auxiliary buttons with programmable function

Note:

• in automatic cycle, the encoder can change the value of the feed override.
• in manual, the enable command button can reset the selected axis.

• n.1 Handwheel
• n.1 wire
• n.1 Mounting bracket
• fixing screws

With the product ordering code it's possible to obtain exactly the features.
Check that the product features match your needs.

The RosettaCNC HandWhell B product is available in the following version:

Drilling template for the panel connector.

Volantino		Connettore CN11 su RosettaCNC Board A
	black	1
	marrone	2
	orange	3
	light blue	4
	blue	5
	green/black	6
	light blue/black	7
	transparent/black	8
		9
	red	10
	prune
	yellow	11
	white	12
		13
		14
	transparent		Da collegare in serie al circuito di arresto per emergenza
	violet
	grigio		Da collegare in serie al circuito di arresto per emergenza
	grigio/black

The following wires remain disconnected:

• pink/black
• orange/black

Green , rosso/black e pink can be connected to any User Input and assigned a function in the RosettaCNC control software.

To connect the handwheel to the RosettaCNC board A, insert the connector into the CN11 as shown in the picture:

Picture 1. Handwheel Installation

For examples of connection of emergency circuits see the product manual RosettaCNC Board A.

Handwheel		Connettore CN17 su RosettaCNC Board B
	red	1A	Collegare: 5A⇔5B 6A⇔6B 7A⇔7B
	yellow	2B
	white	3B
	orange/black	4A
	black	7A
		Connettore CN19 su RosettaCNC Board B
	marrone	2
	orange	3
	light blue	4
	blue	5
	green/black	6
	light blue/black	7
	transparent/black	8
	pink/black	9
	transparent		Da collegare in serie al circuito di arresto per emergenza
	violet
	grigio		Da collegare in serie al circuito di arresto per emergenza
	grigio/black

Green , rosso/black e pink can be connected to any User Input and assigned a function in the RosettaCNC control software.

To connect the handwheel to the RosettaCNC board B, insert the connectors CN17 and CN19 as shown in the picture:

Figure 2. Installation

For examples of connection of emergency circuits see the product manual RosettaCNC Board B.

To use the handwheel, you must set the highlighted values in the followinf picture (In the “RosettaCNC board settings” Panel):

HAndwheel setting

All those who want to contribute to the improvement of this documentation are in advance thanks to the reporting inaccuracies or incorrect content. Write to the address: support@rosettacnc.com