RosettaCNC Handwheel B - Installation and Maintenance manual
Dear Customer,
Thank you for purchasing this product. This document collect all the necessary information for the installation and use of this accessory
Need help ?
Write in the Forum on the www.RosettaCNC.com site or send an email to the following address: support@rosettacnc.com, the RosettaCNC development team will be happy to answer you in a short time.
All rights reserved on this manual. No part of this document can be copied or reproduced in any form without prior written authorisation. RosettaCNC Motion® does not insure or guarantee its contents and explicitly declines all liability related to the guarantee of its suitability for any purpose. The information in this document can be changed without notice. RosettaCNC Motion® shall not be held liable for any error or omission in this document. RosettaCNC Motion® is a registered trademark.
Informations
Document: | MIMROSETTACNCHANDWHEELB | |||
---|---|---|---|---|
Description: | Installation and Maintenance manual | |||
Link: | http://wiki.rosettacnc.com/doku.php/en/hardware/rosettacncboard/mimrosettacnchandwheelb | |||
Document Release | Hardware Version | Description | Note | Date |
01 | 01 | / | 25/10/2021 |
1. Introduction
1.1 General description
For the manual movements (jog) there is a RosettaCNC Handwell A accessory. It has an ergonomic shape that makes it easy to use And is contained in a sturdy anti-shock box. It is equipped with magnets that guarantee a reliable fixation, The electrical connection cable with the RosettaCNC controller It is equipped with a steel wire that increases its reliability and a removable connector with anti-vibration spring contacts.
Handwell B has :
- a double enable command button
- the emergency button with two contacts
- a selector for choosing the axis on which to act
- a three-position switch 1 – 1/10 – 1 /100 that defines the encoder unit of measurement.
- an encoder to execute the movement of the selected axis
- three auxiliary buttons with programmable function
Note:
- in automatic cycle, the encoder can change the value of the feed override.
- in manual, the enable command button can reset the selected axis.
1.2 Symbols used in the manual
Useful Information and tips.
Warnings, failure to comply with these warnings may result in inappropriate operation or damage to the device.^
Potential danger and possible risk of injury.^
1.3 Package Contents
1.4 Product Identification
With the product ordering code it's possible to obtain exactly the features.
Check that the product features match your needs.
1.4.1 Product label
- a - Ordering Code
- b - Week made: indicates the week and year of manufacture
- c - Part number: unique code that identifies an ordering code
- d - Serial number: product serial number, different for individual product
- e - Hardware release: version of hardware release
1.4.2 Ordering code
The RosettaCNC HandWhell B product is available in the following version:
Model | Part number | Description |
---|---|---|
94030031 | RosettaCNC Handwheel B | Without any connectors |
94030032 | RosettaCNC Handwhell B/CBL | Handwheel with circular connectors and without the wired orange connector |
94030033 | RosettaCNC Handwhell B/WDA | Handwheel with circular connectors and with wired orange connector suitable for Rosettacnc A |
94030034 | RosettaCNC Handwhell B/WDB | Handwheel with circular connectors and with wired orange connectors suitable for Rosettacnc B |
94030037 | RosettaCNC Handwheel B/WPA | Handwheel with sectionable cable gland and with wired orange connector suitable for Rosettacnc A |
94030038 | RosettaCNC Handwheel B/WPB | Handwheel with sectionable cable gland and with wired orange connectors suitable for Rosettacnc B |
1.4.3 Specification
Name | Description |
---|---|
Emergency button | two contacts normally closed |
Enable buttons | enable Handwheel commands |
Auxiliary Buttons | three programmable buttons |
Switch | 3 positions, 1 - 1/10 - 1/100 |
Selector | 7 positions, OFF - X - Y - Z - 4 - 5 - 6 |
Encoder | 400 divisions for revolution |
Cable | with steel wire, length 1,7m (3m stretched) |
Support | with magnets |
2. Mechanical installation
2.1 Drilling template
3. Connections
3.1 Cables descriptions
3.1.1 Complete cable
3.1.2 Terminals only
Encoder | ||
---|---|---|
PIN | Color | Function |
1 | red | +5V |
2 | black | 0V |
3 | yelow | A |
4 | white | B |
Axes | ||
5 | brown | X |
6 | orange | Y |
7 | light blue | Z |
8 | blue | 4 |
9 | pink/black | 5 |
10 | orange/black | 6 |
Multiplier | ||
11 | green/black | x1 |
12 | light blue/black | x10 |
13 | transparent/black | x100 |
Auxiliary buttons | ||
14 | green | - |
15 | red/black | ∼ |
16 | pink | + |
Common | ||
17 | plum | COM1 |
Emergency | ||
18 | transparent | NC1A |
19 | purple | NC1B |
20 | gray | NC2A |
21 | gray/black | NC2B |
3.2 Connections with RosettaCNC Board A
This product is compliant only with RosettaCNC Board A hardware version 1.2 or greater.
Volantino | Connettore CN11 su RosettaCNC Board A | ||
---|---|---|---|
black | 1 | ||
marrone | 2 | ||
orange | 3 | ||
light blue | 4 | ||
blue | 5 | ||
green/black | 6 | ||
light blue/black | 7 | ||
transparent/black | 8 | ||
9 | |||
red | 10 | ||
prune | |||
yellow | 11 | ||
white | 12 | ||
13 | |||
14 | |||
transparent | Da collegare in serie al circuito di arresto per emergenza | ||
violet | |||
grigio | Da collegare in serie al circuito di arresto per emergenza | ||
grigio/black |
The following wires remain disconnected:
- pink/black
- orange/black
Green , rosso/black e pink can be connected to any User Input and assigned a function in the RosettaCNC control software.
3.2.1 Installation
To connect the handwheel to the RosettaCNC board A, insert the connector into the CN11 as shown in the picture:
Picture 1. Handwheel Installation
Check the emergency button connection in accordance with the safety circuit of the machine.
For examples of connection of emergency circuits see the product manual RosettaCNC Board A.
3.3 Connections with RosettaCNC Board B
Handwheel | Connettore CN17 su RosettaCNC Board B | ||
---|---|---|---|
red | 1A |
Collegare: |
|
yellow | 2B | ||
white | 3B | ||
orange/black | 4A | ||
black | 7A | ||
Connettore CN19 su RosettaCNC Board B | |||
marrone | 2 | ||
orange | 3 | ||
light blue | 4 | ||
blue | 5 | ||
green/black | 6 | ||
light blue/black | 7 | ||
transparent/black | 8 | ||
pink/black | 9 | ||
transparent | Da collegare in serie al circuito di arresto per emergenza | ||
violet | |||
grigio | Da collegare in serie al circuito di arresto per emergenza | ||
grigio/black |
Green , rosso/black e pink can be connected to any User Input and assigned a function in the RosettaCNC control software.
3.3.1 Installation
To connect the handwheel to the RosettaCNC board B, insert the connectors CN17 and CN19 as shown in the picture:
Check the emergency button connection in accordance with the safety circuit of the machine.
For examples of connection of emergency circuits see the product manual RosettaCNC Board B.
4. Settings
To use the handwheel, you must set the highlighted values in the followinf picture (In the “RosettaCNC board settings” Panel):
5. Acknowledgement
All those who want to contribute to the improvement of this documentation are in advance thanks to the reporting inaccuracies or incorrect content. Write to the address: support@rosettacnc.com